After years of construction and optimization, China Mobile Metropolitan Area Transport Network based on SDH/MSTP technology has better met the transmission requirements of TDM-based voice services and a small number of data services, but the advent of 3G and full-service operations has enabled The IP-based data service becomes the main body of the metropolitan area network transmission. Although SDH/MSTP also has multi-service bearer capability, the TDM-based kernel makes it less efficient, more complex to configure, and less flexible and scalable when carrying IP packet services. Packet-based core-based transport technology PTN After rapid development in recent years, it has gradually matured and is expected to become the next generation mainstream technology to replace SDH. Therefore, China Mobile launched a pilot project of IP transmission project in Hangzhou Mobile to test the feasibility of PTN networking.
1. Introduction to PTN
PTN is a packet-oriented transport network and technology. It is located in the metropolitan area network convergence access layer, with packet switching as the core and provides multi-service support. It has the characteristics of data communication network networking flexibility and statistical multiplexing transmission. It also inherits the advantages of traditional optical transport network for connection, fast protection, and strong OAM capability.
PTN implements connection-oriented fast forwarding through the label switching mechanism; end-to-end simulation of various non-packet services through PWE3 technology; end-to-end QoS control through DiffServ model; CIR (guaranteed bandwidth) and PIR (burst bandwidth) The mechanism implements statistical multiplexing; provides accurate frequency and time synchronization through technologies such as synchronous Ethernet, IEEE 1588v2, and ToP; provides device protection, linear multiplex section protection, MPLS Tunnel APS, LAG, and FRR, and other rich protection modes and similar SDH Carrier-class OAM capabilities. The integration of multiple technologies has laid a good foundation for PTN to carry 3G base stations and full service with high efficiency and high quality.
PTN has two technical standards of MPLS-TP and PBT in its implementation, which are derived from the improvement of MPLS technology and Ethernet technology. The Huawei PTN series equipment used in the pilot of the Hangzhou Mobile IP Transmission Project uses MPLS-TP technology.
2. PTN networking and protection
PTN is a brand-new equipment standard. Its working mechanism and possible business models are very different from SDH. In order to give full play to the advantages of PTN, the new PTN is more suitable for 3G and full-service competition. Zhejiang Mobile organization experts in the province have discussed the networking model and protection mode of PTN in detail, and combined with the deployment of OTN to develop a better networking and protection scheme.
In terms of the networking model, the bandwidth demand of each access point in the 3G era may increase by more than 10 times compared with the 2G era, causing the bandwidth pressure of the core layer and the backbone layer to rise sharply. If the 10 Gbit/s ring is configured in the same manner as the SDH/MSTP network, it is easy to expand the bandwidth of the core backbone ring. The expansion cost of the ring structure is high and the flexibility is poor. Therefore, the networking model of the core layer and the backbone layer has become the focus of PTN network structure optimization considerations. The final solution is to simplify the PTN structure with the help of OTN's high-capacity service provision and carrier-class protection.
As shown in Figure 1, when the PTN device is deployed, the access layer and the aggregation layer still use a ring structure to form the system. The access layer uses the GE rate, and the aggregation layer uses the ten-gigabit Ethernet rate ring. The structure of the two-node loop prevents the single node failure risk of the aggregation node and the backbone node. Instead of building a ring system at the backbone layer, each backbone layer node is directly connected to the relevant core layer node through a GE or a 10 Gigabit Ethernet link provided by the OTN. At the same time, two large PT N devices are configured in each core equipment room, which is responsible for the access of the service port of the equipment room and the scheduling of services, and implements security sharing.
In terms of protection, the SNCP protection of the SDH network is implemented by establishing an end-to-end MPLS tunnel protection. At the same time, in order to reduce the risk of simultaneous failure of the primary and backup tunnels caused by the end-to-end protection path being too long, the backbone layer is on the OTN. The link is then superimposed with a layer of channel protection. For a 3G RNC with a GE interface, the core layer PTN device introduces LAG protection when accessing the RNC interface to avoid a large number of service interruptions caused by single interface failure.
In order to meet the individual requirements of the clients, we offer an extensive range of Tubular Steel Poles and Tubular Poles that are acclaimed among the clients for durable standards and exceptional finishing. We offer them in standard sizes and durable in nature. Steel Tubular Poles are corrosion resistant in nature and is delivered in well-defined time frame.
1.Shape:Conoid ,Multi-pyramidal,Columniform,polygonal or conical
2.Material:steel plate.stainless steel compound plate,stainless steel plate,ect.(anticorrosion treatment with hot galvanization,also color polyester power could be coated on the surface)
High strength low alloy steel Q235,Q345,GR65,GR50 to ensure the mechanical properity of microelement in order to ensure the quality of galvanization (other materials are also avaliable on request)
3.Jointing of pole with insert mode,innerflange mode,face to face joint mode
4.Design of pole :against earthquake of 8 grade ,aganist wind pressure of 160
5.Minimum yield strength:355 mpa
6.Minimum ultimate tensile strength :490 mpa
7.Max ultimate tensilestrength:620 mpa
8.Certificate:ISO9001-2000
9.Length:Within 14m once forming without slip joint
10.Welding:It has past flaw testing.Internal and external double welding makes the welding beautiful in shape
11:Packages:Our poles as normal cover by Mat or straw bale at the top and bottom ,anyway also can following by client required , each 40HC or OT can loading how many pcs will calculation base on the client actually specification and data
Our lighting equipment are made from quality sheet from bending,forming,automatic welding and hot galvanization.We can reach one-run machining length of 14m,and can bend sheet thickness up to 25mm.We adopt advanced welding procedures ,automatically weld main joints and reach rank-II welding quality.
Tubular Pole,Tubular Steel Power Pole,Beautiful Stable Steel Tubular Pole,Tubular Poles,Tubular Steel Poles
YIXING FUTAO METAL STRUCTURAL UNIT CO.,LTD( YIXING HONGSHENGYUAN ELECTRIC POWER FACILITIES CO.,LTD.) , https://www.chinasteelpole.com