Lynx Box 1S+ Nickname M10
It can be known from official propaganda that M10 is not a descendant of Box 2 (TMB300A) but an upgrade to Box 1S (TMB2200RA). The appearance and price are also consistent with the previous generation. Then the question has come. In the end what has been upgraded?
Exterior:
Designers are very peace of mind to maintain the same appearance, and even removed the top of the LOGO. This is the only difference between positive 1S and 1S+
Even the back is the same... (what did the designer hire?)
Behind the interface is the key, 1S original interface all reserved
Based on this, there is one more AV interface, this interface can output audio with HDMI synchronization.
The appearance is like this, except that the interface is almost unchanged then disassembled:
With the same dismantling method as 1S, it is very easy to tear down the cat mask with the teardown film.
Tmall Box 1S+ and 1S 3 screws
Even cat masks are the same
The front of the motherboard. Completely different layout with 1S, new design. The original appearance is just an illusion
There is only one THGBMBG6D1KBAIL on the front of the motherboard. Google knows that it is Toshiba's 19nm memory chip, which has a single capacity of 8GB, which is consistent with the publicity.
In the upper left corner of the main board, the original design in the white box should have an interface, and the unknown reason is deleted.
It is difficult to remove the main board after the two screws fixing the main board are removed. The reason is that the two layers of thermal paste are stuck.
The motherboard processor + memory particles heat conductive glue first to the heat to the shield shell, and then through the conductive shell on the conductive adhesive lead to the weight. The measured long-term operation is stable and the heat dissipation design is stable.
The cat's magic box 1S+ has greatly changed the wifi antenna. On the map, you can see that the cat's magic box 1S+ discards the on-board antenna and switches to an antenna design similar to that of a notebook. The measured signal can be compared with the MBA to avoid the wireless signal can not reach the back of the living room TV.
Tucao about the previous use of the TV box, in order to reduce the size of the antenna for the sake of good light and reduce the output interface. Orz, is this designed for use or for good looks? In order to use a TV box, I'm too drunk.
1S+ uses 4 memory
The main processor adopts A9 architecture, 4 core 2GHz frequency AML8726-M8 processor, and Mali-450MP GPU. The book parameters are very good, actually used? To run and run points.
Samsung particles, single 256MB. 4 pieces of 1GB memory
IP101GR wired network chip, 100Mbps bandwidth
RN5T618M, Ricoh Power Management IC
The Wifi chip is separately covered under the shielding case, and the RTL8192EU is Realtek's RTL8192EU when the shielding case is opened. Google knows that the maximum transmission rate is 300Mbps.
All interface standards, neat, welding firm.
A remote control that has been criticized since the early days of the Lynx Box. The problem of designing and manufacturing remote controllers in the first generation has led to a large number of friends who have lost their power quickly, leaked currents, are insensitive, or simply failed. So what is the improvement of the 1S+ remote control?
That's right, very stable and old-fashioned infrared transmission buy big or buy small: Lynx Box 1S+ dismantling test. Infrared transmission is as obvious as its disadvantages.
The advantage is that it is sufficiently stable and energy-efficient. Even if it is hung up, it can find a universal remote control pairing without the need to purchase an expensive original remote control.
But designers can't be so lazy, I still want to put the box behind the TV... The IR remote must be aligned to work
Powered by 2 AAA batteries, it is not only better to buy but also cheaper than 2032 button batteries.
The internal structure of the remote controller is very simple
The orange M-key is this way
Like a sandwich. There is a layer of film on the front of the remote control board.
The only chip on the remote
Dual signal emitters, adequate fault tolerance
The remote control also has a blue indicator light. After pressing the button, it tells you "I have a transmitting signal. If nothing happens, you are not aligned."
It can be known from official propaganda that M10 is not a descendant of Box 2 (TMB300A) but an upgrade to Box 1S (TMB2200RA). The appearance and price are also consistent with the previous generation. Then the question has come. In the end what has been upgraded?
Exterior:
Designers are very peace of mind to maintain the same appearance, and even removed the top of the LOGO. This is the only difference between positive 1S and 1S+
Behind the interface is the key, 1S original interface all reserved
Based on this, there is one more AV interface, this interface can output audio with HDMI synchronization.
The appearance is like this, except that the interface is almost unchanged then disassembled:
With the same dismantling method as 1S, it is very easy to tear down the cat mask with the teardown film.
Tmall Box 1S+ and 1S 3 screws
Even cat masks are the same
The front of the motherboard. Completely different layout with 1S, new design. The original appearance is just an illusion
There is only one THGBMBG6D1KBAIL on the front of the motherboard. Google knows that it is Toshiba's 19nm memory chip, which has a single capacity of 8GB, which is consistent with the publicity.
In the upper left corner of the main board, the original design in the white box should have an interface, and the unknown reason is deleted.
It is difficult to remove the main board after the two screws fixing the main board are removed. The reason is that the two layers of thermal paste are stuck.
The motherboard processor + memory particles heat conductive glue first to the heat to the shield shell, and then through the conductive shell on the conductive adhesive lead to the weight. The measured long-term operation is stable and the heat dissipation design is stable.
The cat's magic box 1S+ has greatly changed the wifi antenna. On the map, you can see that the cat's magic box 1S+ discards the on-board antenna and switches to an antenna design similar to that of a notebook. The measured signal can be compared with the MBA to avoid the wireless signal can not reach the back of the living room TV.
Tucao about the previous use of the TV box, in order to reduce the size of the antenna for the sake of good light and reduce the output interface. Orz, is this designed for use or for good looks? In order to use a TV box, I'm too drunk.
1S+ uses 4 memory
The main processor adopts A9 architecture, 4 core 2GHz frequency AML8726-M8 processor, and Mali-450MP GPU. The book parameters are very good, actually used? To run and run points.
Samsung particles, single 256MB. 4 pieces of 1GB memory
IP101GR wired network chip, 100Mbps bandwidth
RN5T618M, Ricoh Power Management IC
The Wifi chip is separately covered under the shielding case, and the RTL8192EU is Realtek's RTL8192EU when the shielding case is opened. Google knows that the maximum transmission rate is 300Mbps.
All interface standards, neat, welding firm.
A remote control that has been criticized since the early days of the Lynx Box. The problem of designing and manufacturing remote controllers in the first generation has led to a large number of friends who have lost their power quickly, leaked currents, are insensitive, or simply failed. So what is the improvement of the 1S+ remote control?
That's right, very stable and old-fashioned infrared transmission buy big or buy small: Lynx Box 1S+ dismantling test. Infrared transmission is as obvious as its disadvantages.
The advantage is that it is sufficiently stable and energy-efficient. Even if it is hung up, it can find a universal remote control pairing without the need to purchase an expensive original remote control.
But designers can't be so lazy, I still want to put the box behind the TV... The IR remote must be aligned to work
Powered by 2 AAA batteries, it is not only better to buy but also cheaper than 2032 button batteries.
The internal structure of the remote controller is very simple
The orange M-key is this way
Like a sandwich. There is a layer of film on the front of the remote control board.
The only chip on the remote
Dual signal emitters, adequate fault tolerance
Featuring an original and unique design, our tattoo chair is made of nice touching upholstery. It has been developed for professional tattoo artists.
A totally innovative product that features an impressive look, adapted to the sector needs and that will make your job very comfortable.
Tattoo Bed,Hydraulic Tattoo Bed,Tattoo Massage Table,Portable Tattoo Bed
TOM SPA BEAUTY SALON EQUIPMENT CO.,LTD , https://www.tomspabeauty.com