At present, the LED fluorescent lamp market is very active, and the manufacturers are mainly divided into three categories: one is the factory that originally made the LED chip , and the downstream is infiltrated into the downstream, and there is not much knowledge about the circuit knowledge and the LED fluorescent lamp power supply; the second type is the original ordinary lighting. The factory, entering a new field, knows some about circuit knowledge; the three types are completely new factories. They used to do other products or new ventures, and they have some understanding of LED power supply, and some don’t understand. The LED fluorescent lamp power supply is the most important component of the LED fluorescent lamp. If the LED fluorescent lamp is not properly selected, the LED fluorescent lamp cannot perform its performance or even function normally.
1. Why must we always have a constant flow:
The characteristics of LED semiconductors determine that they are greatly affected by the environment. For example, if the temperature changes, the current of the LED increases, and the voltage increases, and the current of the LED also increases. Long-term operation beyond the rated current will greatly shorten the service life of the LED. The LED constant current is to ensure that its operating current does not change when environmental factors such as temperature and voltage change.
2. Matching of LED fluorescent lamp power supply and lamp board:
Some customers first design the light board, then find the power supply, and find that it is difficult to have a suitable power supply, or the current is too large, the voltage is too small (such as I>350mA, V<40V); or the current is too small, the voltage is too high (such as I< 40mA, V>180V), the result is severe heat, low efficiency, or insufficient input voltage range. In fact, choosing the best string parallel connection method, the voltage and current applied to each LED is the same, and the power supply effect can achieve the best performance. The best way is to communicate with the power supply manufacturer and tailor it.
3, LED working current:
The rated working current of the general LED is 20 mA. Some factories use it at the beginning, and design 20 mA. In fact, the working heat at this current is very serious. After many comparison tests, it is ideal to design 17 mA. . The total current of the N parallel connection = 17*N;
4, LED working voltage:
The recommended working voltage of general LED is 3.0-3.5V. After testing, most of the work is 3.125V, so it is reasonable to calculate according to 3.125V. The total voltage of M lamp beads in series = 3.125*M
5, LED lamp board series and parallel and wide voltage:
In order for the LED fluorescent lamp to operate in the wide range of input voltage range AC85-265V, the LED string parallel connection mode of the light board is very important. Since the current power supply is generally a non-isolated buck power supply, when a wide voltage is required, the output voltage should not exceed 72V, and the input voltage range can reach 85-265V. In other words, the number of series is no more than 23 strings. Do not use too many parallels, otherwise the operating current is too large and the heat is severe. It is recommended to be 6 and /8 and /12. The total current does not exceed 240 mA. There is also a wide voltage scheme, which is to use L6561/7527 to raise the voltage to 400V, and then step down, which is equivalent to two switching power supplies, which cost twice as much. This solution is not cost-effective and has no market.
Far Infrared Heat Film is good for human's health care,it's mainly used in PET heater film for cold-proof face mask,direct selling health care mask polyimide (PI) film,masking film electrical heating Polyimide Film, electric heating sheet mask,health eye mask carbon fiber heating film,Infared Heating film,keep fit heating film, Heating Film For Eye,eye massage thin heated element etc.we are a professional and leader Chinese exporter of heat film,Customization options (for example: SMT components, flex cable and connectors) can provide the perfect complete solution that can significantly reduce assembly time and increase productivity.Providing a variety of complex shapes design, and different power designs. Membrane in the same piece electrically heated heating circuit can be designed and holding circuit,we are looking forward to your cooperation.
Health Care Heat Film For mask
Health Care Heat Film For Mask,Body Heat Film,Infared Heating,Heating Film For Eye
ShenZhen XingHongChang Electric CO., LTD. , https://www.xhc-heater.com