Inverter password (super universal password) - Solutions - Huaqiang Electronic Network

The high-frequency needle JTK-50L-Q features 5 needles for precise applications.

Photocoupler for electrical isolation and signal transmission.

1. Delta Inverter B Series Super Password: 57522 Delta Super Drive Password (H Series): 33582 Delta S1 Series Universal Password: 57522 2. Ouro Inverter (formerly Hui Feng Inverter) Super Password: 1888 The models 1500-G, 1500-P, 1000-G, and 200-G all support universal access. 3. Shuopu Frequency Converter Advanced Menu Settings: - P301: Input 321 - A000: Input 11 to refresh the program - P301: Input 321 again - A000: Enter 9 to access the menu - E001: Input "G" or "P" - E002: Rated Voltage - E003: Rated Current - E004: Voltage Correction - E005: No Movement - E006: Current Correction 4. General PI2000 Refresh Setting Method: - Set C01 to 222 and enter P14 - Set P14 to 3, then CPU will refresh and display PI2000 - Set C01 to 222 to enter P14 parameter settings - Set P14 to 2, P01 to model G/F, P02 to 380V, P03 to rated current, P04 to voltage display, P05 to current display 5. Yingwei Teng Universal Password: 50112 - For models CHV, CHE, CHF, regardless of the password set in P7-00, the universal password is always 50112 6. No password means no access. For Mitsubishi 740, remove the panel and reinsert it. 7. Emerson TD3000 Password: 8888 Emerson TD3300 Password: 2002 8. Xilin Inverter Universal Password: 6860 (previously known, now widely used). 9. ABB ACS600 Inverter Full Parameter Password: - NAMC Main Control Board: - Enter password in parameter 16.03: 2303 - Set 102.01 to "false" to access all main control board parameters 10. Yaskawa G5 Inverter Password: Displayed in A1-04. Press and hold MENU and RESET for 10 seconds to view the password. Transfer it to A1-05 and input to modify parameters. 11. Yaskawa G7 Inverter Password: When A1-04 is displayed, press RESET while holding MENU to show the password setting in A1-05. Input the password into A1-04 to gain access. 12. Hitachi J300 Inverter Factory Reset: Rename a multi-function terminal as "Initialization" (parameters C0-C7), short-circuit it with CM1 or P24, turn off the inverter, and power it back on. To change terminal "7" to "Initialize," set parameter C6 to "7." 13. Delta A Series Inverter Keyboard Lock: Press MODE and RESET together to display P256. Change 00 to 01 and exit to unlock all parameters. 14. Jiaxin TX-4T040C Inverter: Parameters cannot be modified. F00 is the user password (factory default: 8888). Short JP4 (an empty terminal above the CPU) to restore factory password. After entering 8888, you can modify parameters beyond F00. 15. Fuji VG3, VG5, VG7 Elevator Inverters: - VG5: Set last parameter 200 to 0 for no changes, 1 for editable data - VG7: Universal password is FFFF 16. Xiwei Inverter Password: Enter 28622 in SERVICE mode. 17. Schneider Inverter Password: Find COD in SUP menu and enter 6969. 18. 6SE70 Inverter Password: Cannot open. Change P358 and P359 to the same value. 19. TECO M3 Series Inverter: - P00 = 05 to see 65 parameters - P00 = 08 for 2-wire system initialization - P00 = 03 for parameter access 20. Sanchao Inverter Universal Password: CD900 (some sources suggest 365; shared from the internet for reference)